Buschur BADBISH 250x90 Test 3    SportCompact    Buschur BADBISH 250x90 Test
Page 1 of 2 12 LastLast
Results 1 to 20 of 28

Thread: My evo project

  1. #1
    Join Date
    May 2005
    Location
    hell, michigan
    Posts
    18,192,626

    Default My evo project

    I know some of you have seen my thread on evom, but I figure for those who haven't here is how the car has progressed. I know I don't post much over here anymore, but for all who seen the car at the shootout yeah its definately fixed now. That and I would like to share with those who I don't get to see but once a year.

    05 Evo RS 60k miles
    562 whp 438 ft lbs of tq
    34 psi


    Motor
    =====
    stock block stock head
    Gsc s2 cams
    Gsc springs and retainers
    Milspec 65mm tb
    Map rev 3 intake
    Map ported exhaust mani
    Sparktech non cdi coil on plug
    Arp head studs
    Buschur double pumper
    Fic 1450's with e85
    4 inch intake with K&N filter
    Zeitronics wideband and lcd display
    Gates timing belt and balance shaft belt

    Tuning
    =====
    Stock evo ecu
    Tephra v7 with speed density
    and of course the master of tuning Mr Tscompusa

    FMIC
    ====
    Ams with pipeing

    Turbo
    ====
    Map ef4 with ported hot side
    ported exhaust side
    coated and 25lb internal wga
    Grimspeed 3 port

    Exhaust
    ======
    Buschur cat back exhaust with Magnaflow muffler
    Buschur down pipe
    Buschur o2 housing


    Trans
    =====
    stock trans
    stock t case
    Exedy hd twin

    Suspension
    ========
    Koni coil overs and springs
    Tein camber plates
    Engles camber bolts

    Shoes
    =====
    Enkie Nto3's
    Michelin Pilot a/s 255 40 zr17's
    stock evo 8 Enkie's with Blizaks for winter

    Brakes
    ======
    Stock 4 piston Brembo's
    Racing Brake 2 piece front and rear rotors drilled sloted
    Racing Brake ET 500 pads
    SS lines around



    Smoothing 10 551/431 @34 psi

    Final for now more boost + more timing + leaner afr = this




    Let the #s speak for themselves. Any Questions?

    The car is far from done as well. This tune I have is basically gonna get me by till I can get some more parts on the car being I will need more fuel really soon.
    Last edited by brian 5150; 03-23-2012 at 08:13 PM.
    92 talon tsi awd the project that will never run again

    05' EVO RS: stock motor, Map rev3 & ported exhaust mani, Map ef4 turbo, Milspec 65 mm tb, Ams fmic, Buschur stages 1-5, Buschur double pumper, GSC S2 cams with GSC springs and retainers, Zeitronics wb, Exedy hd twin, Sparktech non cdi, Koni coil overs, Enkie nto3's, fic 1450's, Grimmspeed 3 port, tephra v7 SD



    TSCOMPTUNED

    562/438tq @ 34 psi



    Any questions about my setup feel free to ask me.

  2. #2
    Join Date
    Jun 2008
    Location
    living under the buschur dyno
    Posts
    2,932

    Default

    oh man i thought you were using mustang numbers, booooo lol jk
    DB quote "....this isn't some chinese piece of shit...."

  3. #3
    Join Date
    May 2005
    Location
    hell, michigan
    Posts
    18,192,626

    Default

    Don't hate not everyone has access to a dyno in there garage. Although I could have gotten a old old mustang back in the day for 75k used in a going out of business sale, but I had prioritys like guns and finishing the drywall.
    92 talon tsi awd the project that will never run again

    05' EVO RS: stock motor, Map rev3 & ported exhaust mani, Map ef4 turbo, Milspec 65 mm tb, Ams fmic, Buschur stages 1-5, Buschur double pumper, GSC S2 cams with GSC springs and retainers, Zeitronics wb, Exedy hd twin, Sparktech non cdi, Koni coil overs, Enkie nto3's, fic 1450's, Grimmspeed 3 port, tephra v7 SD



    TSCOMPTUNED

    562/438tq @ 34 psi



    Any questions about my setup feel free to ask me.

  4. #4
    Join Date
    Jun 2008
    Location
    living under the buschur dyno
    Posts
    2,932

    Default

    lol i drive to buschur to use the dyno there since it reads low as hell
    DB quote "....this isn't some chinese piece of shit...."

  5. #5
    Join Date
    May 2005
    Location
    hell, michigan
    Posts
    18,192,626

    Default

    If you really wanted mustang #s Johnny the car made 475/386 and no offence but I would take it to Pure being they have the same dyno and there 2 hours closer.
    92 talon tsi awd the project that will never run again

    05' EVO RS: stock motor, Map rev3 & ported exhaust mani, Map ef4 turbo, Milspec 65 mm tb, Ams fmic, Buschur stages 1-5, Buschur double pumper, GSC S2 cams with GSC springs and retainers, Zeitronics wb, Exedy hd twin, Sparktech non cdi, Koni coil overs, Enkie nto3's, fic 1450's, Grimmspeed 3 port, tephra v7 SD



    TSCOMPTUNED

    562/438tq @ 34 psi



    Any questions about my setup feel free to ask me.

  6. #6
    Join Date
    Jun 2008
    Location
    living under the buschur dyno
    Posts
    2,932

    Default

    thats better lol
    DB quote "....this isn't some chinese piece of shit...."

  7. #7
    Join Date
    May 2005
    Location
    hell, michigan
    Posts
    18,192,626

    Default

    Reguardless of which dyno you look at the car feels really good during a pull. Best part is it doesn't smoke anymore we figured out what was causing that.
    92 talon tsi awd the project that will never run again

    05' EVO RS: stock motor, Map rev3 & ported exhaust mani, Map ef4 turbo, Milspec 65 mm tb, Ams fmic, Buschur stages 1-5, Buschur double pumper, GSC S2 cams with GSC springs and retainers, Zeitronics wb, Exedy hd twin, Sparktech non cdi, Koni coil overs, Enkie nto3's, fic 1450's, Grimmspeed 3 port, tephra v7 SD



    TSCOMPTUNED

    562/438tq @ 34 psi



    Any questions about my setup feel free to ask me.

  8. #8
    Join Date
    Jun 2008
    Location
    living under the buschur dyno
    Posts
    2,932

    Default

    the ass dyno is the best one out there lol
    glad to hear the car is running good...ill have to take a ride in it next year
    DB quote "....this isn't some chinese piece of shit...."

  9. #9
    Join Date
    May 2005
    Location
    hell, michigan
    Posts
    18,192,626

    Default

    Well if I can swing it the car will have either a 2.3 or 2.4 in it but who knows. Either that or get some time off and come spend a weekend out here. Just make sure you drag Wills drunk ass and hell mine as well drag Jake and Dan while your at it. Plenty of room out here. Although Dan and Will prob will have to sleep outside in the cold being they are to LOUD when people try to sleep. Don't ask me how I know I only room next to them at the shootout every year hahahaha.
    92 talon tsi awd the project that will never run again

    05' EVO RS: stock motor, Map rev3 & ported exhaust mani, Map ef4 turbo, Milspec 65 mm tb, Ams fmic, Buschur stages 1-5, Buschur double pumper, GSC S2 cams with GSC springs and retainers, Zeitronics wb, Exedy hd twin, Sparktech non cdi, Koni coil overs, Enkie nto3's, fic 1450's, Grimmspeed 3 port, tephra v7 SD



    TSCOMPTUNED

    562/438tq @ 34 psi



    Any questions about my setup feel free to ask me.

  10. #10
    Join Date
    Jun 2003
    Location
    PA
    Posts
    3,822

    Default

    Hey what do you mean we are loud? We keep the partying at a reasonable volume lol
    My car is built with Ebay parts.

  11. #11
    Join Date
    May 2005
    Location
    hell, michigan
    Posts
    18,192,626

    Default

    Being we had a lot of fun that nite if it werent for me lieing to the security about someone fallin into the hot tub accedently you guys would have been thrown out hahaha. How about I will just put you guys in the beer tent out in back and you can knock yourselves out from there. I am sure my neighbors wont care being they drink as much as you guys do and then some being one is Irish and the other is German hahaha.
    92 talon tsi awd the project that will never run again

    05' EVO RS: stock motor, Map rev3 & ported exhaust mani, Map ef4 turbo, Milspec 65 mm tb, Ams fmic, Buschur stages 1-5, Buschur double pumper, GSC S2 cams with GSC springs and retainers, Zeitronics wb, Exedy hd twin, Sparktech non cdi, Koni coil overs, Enkie nto3's, fic 1450's, Grimmspeed 3 port, tephra v7 SD



    TSCOMPTUNED

    562/438tq @ 34 psi



    Any questions about my setup feel free to ask me.

  12. #12
    Join Date
    Jun 2008
    Location
    living under the buschur dyno
    Posts
    2,932

    Default

    dan wasnt there for that lol
    dan is a rag head haha remember the pic with him wearing the armrest cover like a sultan?
    DB quote "....this isn't some chinese piece of shit...."

  13. #13
    Join Date
    May 2005
    Location
    hell, michigan
    Posts
    18,192,626

    Default

    Oh yeah thats right Dan u missed it I saved Will and Johnny from being thrown out this year at the shootout. You picked a bad shootout to miss for sure. But that doesn't count being I have been next to them for the past 6 years.
    92 talon tsi awd the project that will never run again

    05' EVO RS: stock motor, Map rev3 & ported exhaust mani, Map ef4 turbo, Milspec 65 mm tb, Ams fmic, Buschur stages 1-5, Buschur double pumper, GSC S2 cams with GSC springs and retainers, Zeitronics wb, Exedy hd twin, Sparktech non cdi, Koni coil overs, Enkie nto3's, fic 1450's, Grimmspeed 3 port, tephra v7 SD



    TSCOMPTUNED

    562/438tq @ 34 psi



    Any questions about my setup feel free to ask me.

  14. #14
    Join Date
    Jun 2003
    Location
    PA
    Posts
    3,822

    Default

    Quote Originally Posted by mullen View Post
    dan wasnt there for that lol
    dan is a rag head haha remember the pic with him wearing the armrest cover like a sultan?
    Well when you spend has much time as I have over in the sand box that shit grows on you lol.
    My car is built with Ebay parts.

  15. #15
    Join Date
    May 2005
    Location
    hell, michigan
    Posts
    18,192,626

    Default

    Hey I spent tons of time in the sand box when I was a child don't hand me that shit and I don't wear a turbin anyways get back on subject and quit cluttering my build thread hahaha
    92 talon tsi awd the project that will never run again

    05' EVO RS: stock motor, Map rev3 & ported exhaust mani, Map ef4 turbo, Milspec 65 mm tb, Ams fmic, Buschur stages 1-5, Buschur double pumper, GSC S2 cams with GSC springs and retainers, Zeitronics wb, Exedy hd twin, Sparktech non cdi, Koni coil overs, Enkie nto3's, fic 1450's, Grimmspeed 3 port, tephra v7 SD



    TSCOMPTUNED

    562/438tq @ 34 psi



    Any questions about my setup feel free to ask me.

  16. #16
    Join Date
    Jun 2003
    Location
    PA
    Posts
    3,822

    Default

    Not the same sand box lol
    My car is built with Ebay parts.

  17. #17
    Join Date
    Jun 2008
    Location
    living under the buschur dyno
    Posts
    2,932

    Default

    i have no idea what that place is like...
    DB quote "....this isn't some chinese piece of shit...."

  18. #18
    Join Date
    Jun 2003
    Location
    PA
    Posts
    3,822

    Default

    Quote Originally Posted by mullen View Post
    i have no idea what that place is like...
    Oh it's great if you close your eyes turn the AC on and put ear plugs in lol
    My car is built with Ebay parts.

  19. #19
    Join Date
    May 2005
    Location
    hell, michigan
    Posts
    18,192,626

    Default

    I am gonna burry both u rag heads if u dont start talkin cars hahaha.
    92 talon tsi awd the project that will never run again

    05' EVO RS: stock motor, Map rev3 & ported exhaust mani, Map ef4 turbo, Milspec 65 mm tb, Ams fmic, Buschur stages 1-5, Buschur double pumper, GSC S2 cams with GSC springs and retainers, Zeitronics wb, Exedy hd twin, Sparktech non cdi, Koni coil overs, Enkie nto3's, fic 1450's, Grimmspeed 3 port, tephra v7 SD



    TSCOMPTUNED

    562/438tq @ 34 psi



    Any questions about my setup feel free to ask me.

  20. #20
    Join Date
    Jun 2003
    Location
    PA
    Posts
    3,822

    Default

    Lol. We are going to work on my car tomorrow, provided this monsoon stops.
    My car is built with Ebay parts.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •