Forum: Stock Evo 8 / 9 / X / Ralliart ECU

Anyone have the battery offset tables by chance for the bosch 1600cc injectors? Doing a project w/ a bud and he got these. Can't afford FIC/ID's, so lets not go that route.. :p any help? TIA!

I just upgraded to windows 7.. and can no longer, log or flash the ecu. Any fixes.. or am I missing something? I tried running both programs in windows xp compatibility mode with no success.

Ok so I am going to a dyno day on saturday and I wanted to be able to be tuned on E85 by then. I have read through hundreds of pages on evom and feel I have an understanding for what is needed. Right now my AFR's are: Spool ~ 12:1 tapers to 10.8:1 Peak TQ: 11.1:1 stays between 11-11.2 till...

Hey all, I've been posting in one of the SD threads on evoM, but figured I'd copy/paste my posts here and get some discussion going, as I'm still looking for some feedback! I used the off-the-shelf tephra v7 9651706 rom pre-patched for speed density, option 5 in the tephra v7 final thread. ...

Hi guys. Thanks for your help before Bryan, but nothing you gave me worked? What items should I log in obd2 for tuning purposes. I have purchaced evoscan and op2 cable, but it is shit and doesn't work! The only thing I have ever got, that comes with a "no response from the supplier and no tech...

Well I have tested all the big high impedance injectors in the last few weeks as part of my ongoing desire to know things. I will also be posting the settings for the FIC 900 which like its counterpart is a smaller high impedance injector with the capability for high flow at high base pressure. ...

Hey guys, I'm new to ecu flashing, have done a lot of work with microtech's and such... I have been searching threw these forums and evolutionm.net for the past week until 2am every night, and have managed to find ALMOST all i need to continue... I have a OP2 Tactrix cable, LM-2 Innovative...

I was wondering if anyone had the stock tune for an evo 8? mine is a 2005 RS, but i just need the base tune. any help would be appreciated.

I use Tephra's NLTS + Valet + KnockCEL patch and I would like to add the 2-stage knock light capability. I'm not a software guy. Intuitively, it seems like the latter lines of code need to replace the former: <table name="KnockSum Required for CEL" category="Mods" address="480C2" type="1D"...

I have been battling a problem with my car since i bought it over 3 years ago. I put some mods on the car clutch,intercooler,intake,o2 housing,full exhaust, fuel pump, and tune. First tune was done by mellon tuning the problem was the car felt like it was missing something and the two step would...

Well I made the swicth to get rid of the SD Jitter/Jutter that its know for in the low 2000 rpm range. Well I made the switch earlier today and drove the car around. It was a lil rich at idle but fine everywhere else. i just lower the RPM VE at my idle speed int he SD tuning to bring my idle AFRs...

With some help from some key people after finding out that the Evo 10 MR would not run lower than a certain ignition timing at WOT in key areas, we have found a very handy table for the MR. Even more handy for people that only have access to 91 oct. ;) The Upper Bound Ignition Timing table...

So on Tuesday afternoon I took my car up to CBRD to try to finish dialing in my SD patched 94170025 V5.10 ROM. I had to engine redone by Buschur back in June when it made 474 smoothed and 480 unsmoothed back in June thru a stock MAF a 4-3" reducer coupling at around 30 ish psi. David made a...

Well in hopes to take advantage of the NLTS, Valet and CEL mods I made the transition from my original 96420007 to the pre-patched 96420008. Copy and pasted EVERY parameter and it fired up and idled smoothly. Im thinking allright! Tested the valet and the CEL mods, all ok. Went for a drive and it...

Hello stock ECU guru's. I welcome each and everyone of you here. I am willing to set this section of the forums however you'd like. I'd like to give each of you guru's your own section here so you can post all your information you want to share in a well organized manner that is easy to...

Old thread but adding it to this forum: I'm starting this thread now since I had some free time over the thanksgiving holiday to actually put some time into making this. This first posting will be ever evolving with updates and new information EcuFlash tables and what they do:...